If you have already tried to install the drivers for EPSON L3250 but the installation ended with an error, especially when installing the scanner, it is not recommended to simply run the installers again. It is better to first remove the previous failed installation, restart the computer, and then install the printer driver and scanner driver separately.<\/p>\n
Below is the procedure for Windows 11 and Windows 10 64-bit<\/strong>. The primary connection method is USB. It is convenient for troubleshooting installation errors because it lets you first verify that the driver itself works without adding possible Wi-Fi network configuration problems.<\/p>\n For normal operation of the multifunction printer, two main packages are required:<\/p>\n For the 64-bit systems covered here, the following installation files are used:<\/p>\n The driver version on the Epson website may change over time. If you download the files again, select the driver specifically for Windows 11 64-bit<\/strong> or Windows 10 64-bit<\/strong> and download it from the official EPSON L3250 support page.<\/p>\n The additional Epson ScanSmart software is not required for basic scanning. Epson Scan 2<\/strong> is installed together with the scanner driver. This program is usually sufficient for scanning documents and photos.<\/p>\n If the driver has already been installed and the installation ended with an error, it is better to perform the new installation after removing the old components. Epson also recommends uninstalling and reinstalling the software when similar problems occur.<\/p>\n This step is not always necessary. Perform it if the installation has already failed several times or Windows continues to detect an old Epson device after the software has been removed.<\/p>\n After removal, restart the computer<\/strong>. The EPSON L3250 USB cable must remain disconnected until the new installation begins.<\/p>\n Windows 11 includes Windows protected print mode<\/strong>. If it is enabled, Windows uses its own modern printing mechanism and does not allow conventional third-party printer drivers to be installed.<\/p>\n If the EPSON L3250 driver does not install, check this setting before reinstalling it.<\/p>\n If this setting is not present in your version of Windows 11 or is already disabled, you do not need to change anything.<\/p>\n For Windows 10, this section can be skipped.<\/p>\n After removing the previous installation, install the printer driver first.<\/p>\n You can choose to set the printer as the default printer if desired. Automatic software updates are not required for the driver installation itself.<\/p>\n After the installation begins, the program will prepare the driver and proceed to device detection.<\/p>\n For the initial installation and troubleshooting, it is not recommended to connect the multifunction printer through a USB hub, docking station, or long extension cable.<\/p>\n First, wait for a while after connecting the powered-on multifunction printer. If the device is still not detected:<\/p>\n If automatic detection still does not work, you can open Setup<\/strong> in the installer, select USB connection<\/strong>, and continue the installation manually.<\/p>\n After the device is detected, wait until the installation is fully completed. If the program asks you to restart the computer, restart it.<\/p>\n After installing the printer driver, the scanner components must be installed separately.<\/p>\n Use the file:<\/p>\n The Epson Scan 2<\/strong> program is installed together with the scanner driver. Its features are usually sufficient for basic scanning of documents and photos. You do not need to install the additional Epson ScanSmart software just for simple scanning.<\/p>\n After the installation is complete, open the Start<\/strong> menu, find Epson Scan 2<\/strong>, and launch the program.<\/p>\n Place a document or photo on the scanner glass and perform a test scan.<\/p>\n If the error occurs specifically during installation of the scanner driver, downloading the same file in another browser usually does not solve the problem. The cause may be remnants of the previous installation, temporary Windows files, or an already installed corrupted driver.<\/p>\n Open the list of installed Windows apps and check whether Epson Scan 2<\/strong> appeared there after the failed installation. If it did, uninstall it and restart the computer.<\/p>\n Create the following folder on the system drive:<\/p>\n Copy the This helps rule out problems caused by running the installer from the browser’s temporary folder, a network drive, or a synchronized folder.<\/p>\n If the installation fails again:<\/p>\n If the installation suddenly stops for no clear reason, open Windows Security \u2192 Virus & threat protection \u2192 Protection history<\/strong> and check whether an Epson file or component was blocked.<\/p>\n It is not recommended to completely disable Windows protection just to install the driver. If there are no messages about Epson being blocked in the protection history, leave the protection enabled.<\/p>\n If third-party antivirus software is being used and it displays a specific message that the Epson installer has been blocked, first make sure that you are using the original installation file. Then allow the trusted file to run using the antivirus software’s own controls.<\/p>\n If Epson Scan 2 was installed without errors but the program does not detect the scanner, this is no longer a driver installation error. First check the USB connection.<\/p>\n If the printer is already printing but Epson Scan 2 still does not detect the scanner, open Device Manager<\/strong> and check whether there is a warning icon next to the Epson device.<\/p>\n If such a device is present, remove it, disconnect the USB cable, restart the computer, and reinstall Epson Scan 2.<\/p>\n After the installation is complete, both multifunction printer functions should be tested separately.<\/p>\n Printing:<\/strong> open any small document or page and send it to EPSON L3250 Series<\/strong>.<\/p>\n Scanning:<\/strong> launch Epson Scan 2<\/strong>, place a document on the scanner glass, and perform a test scan.<\/p>\n If you have already tried to install the drivers for EPSON L3250 but the installation ended with an error, especially when installing the scanner, it is not recommended to simply run the installers again. It is better to first remove…<\/p>\nWhich drivers are required for EPSON L3250<\/h2>\n
\n
\n
1. Remove the previous failed installation<\/h2>\n
Windows 11<\/h3>\n
\n
Windows 10<\/h3>\n
\n
If the previous installation was interrupted and the device remains in Device Manager<\/h3>\n
\n
2. Additional check in Windows 11<\/h2>\n
\n
3. Install the EPSON L3250 printer driver<\/h2>\n
\n
L3250_STD_WW_38005_W64.exe<\/code> file and select Run as administrator<\/strong>.<\/li>\nIf the installer does not detect EPSON L3250<\/h3>\n
\n
4. Install the scanner driver and Epson Scan 2<\/h2>\n
EpsonScan2_L3250_67810_41_Signed.exe<\/code><\/p>\n\n
EpsonScan2_L3250_67810_41_Signed.exe<\/code> file.<\/li>\n5. What to do if Epson Scan 2 still does not install<\/h2>\n
Uninstall Epson Scan 2 again<\/h3>\n
Run the installer from a simple local folder<\/h3>\n
C:\\Epson<\/pre>\n
EpsonScan2_L3250_67810_41_Signed.exe<\/code> file into it, then right-click the file and select Run as administrator<\/strong>.<\/p>\nClear temporary installer files<\/h3>\n
\n
%temp%<\/pre>\n
\n
C:\\Epson<\/code> folder as administrator.<\/li>\n<\/ol>\nCheck whether an old scanner device remains<\/h3>\n
\n
Check Windows Security<\/h3>\n
6. Epson Scan 2 is installed, but the scanner is not detected<\/h2>\n
\n
7. Check printing and scanning<\/h2>\n