{"id":78729,"date":"2026-08-16T10:22:42","date_gmt":"2026-08-16T07:22:42","guid":{"rendered":"https:\/\/drivernew.com\/?p=78729"},"modified":"2026-08-16T10:22:42","modified_gmt":"2026-08-16T07:22:42","slug":"oki-mb472-mb492-and-mb562-scan-only-one-side-how-to-enable-duplex-scanning-and-copying","status":"publish","type":"post","link":"https:\/\/drivernew.com\/?p=78729","title":{"rendered":"OKI MB472, MB492 and MB562 Scan Only One Side \u2014 How to Enable Duplex Scanning and Copying"},"content":{"rendered":"<p>If a two-sided document passes through the ADF but only the front sides are saved in the file, this usually does not indicate a scanner malfunction. The OKI MB472, MB492 and MB562 support duplex scanning, but it may be disabled for a new job. You need to enable it in the place from which scanning is started.<\/p>\n<p><strong>ADF<\/strong> stands for Automatic Document Feeder. These models use a reversing ADF: the device scans one side, reverses the sheet inside the feeder, and then scans the other side.<\/p>\n<div style=\"background-color: #eef6ff; border-left: 5px solid #2271b1; margin: 20px 0; padding: 14px 18px;\">\n<p style=\"margin: 0 0 8px;\"><strong>Where duplex mode is enabled<\/strong><\/p>\n<p style=\"margin: 0;\">When scanning to email, a shared folder, or USB memory, the setting is configured on the MFP control panel. When scanning is started from Windows, the source and duplex mode are selected in the program on the computer. Copying uses a separate <strong>Duplex Copy<\/strong> setting on the control panel. Changing one of these settings does not enable the other two.<\/p>\n<\/div>\n<h2>Models covered by this guide<\/h2>\n<p>This guide applies to the following monochrome MFPs:<\/p>\n<ul>\n<li>OKI MB472dn, MB472dnw and MB472w;<\/li>\n<li>OKI MB492dn;<\/li>\n<li>OKI MB562dnw;<\/li>\n<li>OKI ES4172LP MFP and ES4192 MFP;<\/li>\n<li>OKI ES5162 MFP, ES5162dnw and ES5162LP MFP.<\/li>\n<\/ul>\n<p>The OKI MB472 uses a button-based control panel with a 3.5-inch display. The MB492 and MB562 have a touch panel. Therefore, the following procedures are provided separately for these devices.<\/p>\n<h2>Prepare the document and check the ADF<\/h2>\n<p><strong>Where the actions are performed:<\/strong> at the ADF input tray. Windows, the driver, and the scanning program are not used yet.<\/p>\n<ol>\n<li>For the first test, use one flat two-sided A4 sheet of plain paper.<\/li>\n<li>Make sure the sheet has no paper clips, staples, labels, tears, severe folds, or wet ink.<\/li>\n<li>Place the document in the ADF face up.<\/li>\n<li>If the document is in portrait orientation, feed its left edge into the ADF.<\/li>\n<li>If the document is in landscape orientation, feed its top edge into the ADF.<\/li>\n<li>Move the side guides so that they fit exactly against the edges of the sheet, but do not bend it.<\/li>\n<\/ol>\n<p>For testing, it is convenient to write \u201cFront\u201d and \u201cBack\u201d on the two sides of the sheet. After scanning, you will immediately see whether the machine scanned both sides and whether the image orientation is correct.<\/p>\n<div style=\"background-color: #fffbf0; border-left: 5px solid #ff9800; margin: 20px 0; padding: 14px 18px;\">\n<p style=\"margin: 0 0 8px;\"><strong>A6 size limitation<\/strong><\/p>\n<p style=\"margin: 0;\">Automatic duplex scanning of A6 documents is not supported. Use a standard A4 sheet for testing. Damaged, curled, stuck-together, or excessively thick originals should also not be fed through the ADF.<\/p>\n<\/div>\n<h2>Step 1. Enable duplex scanning on OKI MB472<\/h2>\n<p><strong>Where the actions are performed:<\/strong> on the MFP button-based control panel. This method is used when scanning from the control panel to email, a shared folder, or USB memory.<\/p>\n<ol>\n<li>Place the two-sided original in the ADF face up.<\/li>\n<li>Press the physical <strong>SCAN<\/strong> button.<\/li>\n<li>Use the arrow buttons to select the required scanning type in the <strong>Scan Menu<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Specify the email address, shared-folder profile, or another destination depending on the selected method.<\/li>\n<li>Use the arrow buttons to select <strong>Scan Setting<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Select <strong>Duplex Scan<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Select <strong>Long Edge Bind<\/strong> or <strong>Short Edge Bind<\/strong>.<\/li>\n<li>Press <strong>OK<\/strong>.<\/li>\n<li>Press the <strong>START<\/strong> button to begin scanning.<\/li>\n<\/ol>\n<p>The factory setting for <strong>Duplex Scan<\/strong> is <strong>OFF<\/strong>. Therefore, for a new job the machine may scan only the front side even though the ADF itself is working correctly.<\/p>\n<h2>Step 2. Enable duplex scanning on OKI MB492 and MB562<\/h2>\n<p><strong>Where the actions are performed:<\/strong> on the MFP touch panel. The setting applies to a job started from the control panel.<\/p>\n<ol>\n<li>Place the two-sided original in the ADF face up.<\/li>\n<li>On the touch panel, press <strong>Scan<\/strong> or press the physical <strong>SCAN<\/strong> button.<\/li>\n<li>Select the save method: <strong>Scan To E-mail<\/strong>, <strong>Scan To Shared Folder<\/strong>, or <strong>Scan To USB Memory<\/strong>.<\/li>\n<li>Select the recipient, shared-folder profile, or connected USB drive.<\/li>\n<li>When scanning to email or a shared folder, open the <strong>Advanced<\/strong> tab and press <strong>Duplex Scan<\/strong>.<\/li>\n<li>When saving to a USB drive, find <strong>Duplex Scan<\/strong> on the <strong>Scan To USB Memory<\/strong> tab.<\/li>\n<li>Select long-edge or short-edge binding.<\/li>\n<li>If necessary, specify the file format, resolution, and file name.<\/li>\n<li>Press <strong>START<\/strong>.<\/li>\n<\/ol>\n<p>Depending on the firmware version, the <strong>Duplex Scan<\/strong> button may be located on the <strong>Basic<\/strong> or <strong>Advanced<\/strong> tab. The name of the setting itself remains the same.<\/p>\n<h2>How to choose long-edge or short-edge binding<\/h2>\n<p><strong>Where the actions are performed:<\/strong> in the <strong>Duplex Scan<\/strong> setting on the MFP control panel or in the source settings of the scanning program.<\/p>\n<table style=\"border-collapse: collapse; width: 100%; margin: 18px 0;\">\n<thead>\n<tr>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">Document type<\/th>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">How pages are turned<\/th>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">What to select<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Standard portrait document<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">From left to right, like pages in a book<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Long Edge Bind<\/strong><\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Document bound at the top<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">From bottom to top, like pages in a notepad or calendar<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Short Edge Bind<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>If the front side is saved correctly but the reverse side is rotated by 180 degrees, the machine is working correctly. Repeat the job and select the other binding edge.<\/p>\n<h2>Step 3. Check the resulting file<\/h2>\n<p><strong>Where the actions are performed:<\/strong> in a PDF or image viewer on the computer or on the device to which the file was sent.<\/p>\n<ol>\n<li>Open the created file.<\/li>\n<li>Check the number of pages. Two two-sided sheets should produce four scanned pages.<\/li>\n<li>Make sure that the reverse side of each sheet follows its front side.<\/li>\n<li>Check the text orientation on the reverse-side pages.<\/li>\n<li>If only the front sides were saved, repeat the job and, before pressing <strong>START<\/strong>, make sure once again that <strong>Duplex Scan<\/strong> is not set to <strong>OFF<\/strong>.<\/li>\n<\/ol>\n<p>During duplex scanning, the reversing ADF pulls the sheet back into the paper path to scan the second side. The additional sheet movement and a short pause are normal.<\/p>\n<h2>Scanning to a computer from the control panel via WSD<\/h2>\n<p><strong>Where the actions are performed:<\/strong> on the MFP control panel. A WSD scanner must already be registered on the computer.<\/p>\n<h3>OKI MB472<\/h3>\n<ol>\n<li>Place the document in the ADF and press <strong>SCAN<\/strong>.<\/li>\n<li>Select <strong>Computer<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Select <strong>Select A Connecting PC<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Select <strong>From WSD Scan<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Select the computer that should receive the file.<\/li>\n<li>Select <strong>Duplex Scan<\/strong>, set it to <strong>ON<\/strong>, and press <strong>OK<\/strong>.<\/li>\n<li>Press <strong>START<\/strong>.<\/li>\n<\/ol>\n<h3>OKI MB492 and MB562<\/h3>\n<ol>\n<li>Place the document in the ADF and press <strong>Scan<\/strong>.<\/li>\n<li>Select <strong>Scan To Computer<\/strong>.<\/li>\n<li>Press <strong>Select A Connecting PC<\/strong>.<\/li>\n<li>Select <strong>From WSD Scan<\/strong>.<\/li>\n<li>Select the destination computer.<\/li>\n<li>Enable <strong>Duplex Scan<\/strong> and press <strong>START<\/strong>.<\/li>\n<\/ol>\n<div style=\"background-color: #fffbf0; border-left: 5px solid #ff9800; margin: 20px 0; padding: 14px 18px;\">\n<p style=\"margin: 0 0 8px;\"><strong>The control-panel setting does not always apply<\/strong><\/p>\n<p style=\"margin: 0;\">If the job is started by pressing a button in a program on the computer, the source specified in that program&#8217;s profile is used. The <strong>Duplex Scan<\/strong> setting on the MFP control panel cannot force a change to a Windows, WIA, or TWAIN profile.<\/p>\n<\/div>\n<h2>If scanning is started from Windows 11<\/h2>\n<p><strong>Where the actions are performed:<\/strong> in the <strong>Windows Scan<\/strong> app or another scanning program on the computer.<\/p>\n<ol>\n<li>Place the two-sided original in the ADF face up.<\/li>\n<li>Open the <strong>Start<\/strong> menu, type <strong>Windows Scan<\/strong> in the search box, and open the app.<\/li>\n<li>In the <strong>Scanner<\/strong> field, select OKI MB472, MB492, or MB562.<\/li>\n<li>In the <strong>Source<\/strong> field, select the document feeder. Do not select <strong>Flatbed<\/strong>.<\/li>\n<li>If the app displays a setting with the words <strong>Duplex scanning<\/strong> or a separate duplex feeder option, enable it.<\/li>\n<li>Specify the file type and save folder.<\/li>\n<li>Click <strong>Scan<\/strong>.<\/li>\n<\/ol>\n<p>In Windows 11, the MFP is often installed as a WSD scanner. The app may show <strong>Feeder<\/strong> as the source but may not provide a duplex switch. There is no hidden setting in this window that needs to be enabled in the printer properties.<\/p>\n<p>If the duplex option is unavailable, scan from the control panel to a shared folder, email, or USB memory. Another option is to use a program that works with the installed OKI scanner driver through TWAIN or WIA and allows you to select the duplex ADF.<\/p>\n<h2>If scanning is started from Windows 10<\/h2>\n<p><strong>Where the actions are performed:<\/strong> in the <strong>Windows Scan<\/strong> app, <strong>Windows Fax and Scan<\/strong>, or a program that supports WIA\/TWAIN.<\/p>\n<p>In the <strong>Windows Scan<\/strong> app, follow the same steps as in Windows 11: select the MFP, then specify the document feeder in the <strong>Source<\/strong> field. If the duplex option is not displayed, test scanning through a program that uses the OKI WIA or TWAIN driver.<\/p>\n<ol>\n<li>Open the program from which you normally start scanning.<\/li>\n<li>Select the OKI scanner, not another accidentally added device with a similar name.<\/li>\n<li>Open the source or document feeding settings.<\/li>\n<li>Select the ADF option whose name explicitly indicates duplex scanning.<\/li>\n<li>Do not select <strong>Flatbed<\/strong>: this means the large platen glass.<\/li>\n<li>If the driver interface is displayed in English, the source setting may be called <strong>Scan Method<\/strong>. Select an <strong>ADF<\/strong> option containing the word <strong>Duplex<\/strong>.<\/li>\n<li>Run a test using one two-sided sheet.<\/li>\n<\/ol>\n<p>ActKey and some versions of the OKI scanner driver may only provide an English interface. Therefore, the names <strong>Scan Method<\/strong>, <strong>ADF<\/strong>, <strong>Duplex<\/strong>, and <strong>Flatbed<\/strong> may remain in English.<\/p>\n<h2>If there is no duplex source in the Windows program<\/h2>\n<p><strong>Where the actions are performed:<\/strong> first in the program on the computer, and then on the MFP control panel for a test job.<\/p>\n<ol>\n<li>Make sure the ADF is selected rather than the platen glass.<\/li>\n<li>Open the advanced source settings. Some programs show duplex mode only after the ADF has been selected.<\/li>\n<li>Close the program and perform a direct duplex scan from the control panel to USB memory, email, or a shared folder.<\/li>\n<li>If both sides are saved when scanning from the control panel, the ADF is working correctly. The limitation is related to the program, WSD profile, or installed scanner driver.<\/li>\n<li>Use the working control-panel method or another program with TWAIN\/WIA support.<\/li>\n<\/ol>\n<p>Do not reinstall the PCL6 or PS print driver just to make duplex scanning appear. The print driver controls printing and does not add source modes to a scanning program.<\/p>\n<h2>How to configure binding for WSD scanning<\/h2>\n<p>This section is needed if both sides are scanned through WSD but the reverse-side pages are saved upside down.<\/p>\n<h3>OKI MB472<\/h3>\n<p><strong>Where the actions are performed:<\/strong> in the administration menu on the MFP button-based control panel.<\/p>\n<ol>\n<li>Press <strong>SETTING<\/strong>.<\/li>\n<li>Select <strong>Admin Setup<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Enter the current administrator password and confirm the login.<\/li>\n<li>Select <strong>Scanner Setup<\/strong>.<\/li>\n<li>Open <strong>WSD Scan Setup<\/strong>.<\/li>\n<li>Select <strong>Binding<\/strong>.<\/li>\n<li>Set <strong>Long Edge Bind<\/strong> or <strong>Short Edge Bind<\/strong>.<\/li>\n<li>Press the return button until the main screen appears.<\/li>\n<\/ol>\n<h3>OKI MB492 and MB562<\/h3>\n<p><strong>Where the actions are performed:<\/strong> in the administration menu on the MFP touch panel.<\/p>\n<ol>\n<li>Press <strong>Device Settings<\/strong>.<\/li>\n<li>Select <strong>Admin Setup<\/strong>.<\/li>\n<li>Enter the current administrator name and password.<\/li>\n<li>Press <strong>Scanner Setup<\/strong>.<\/li>\n<li>Open <strong>WSD Scan Setup<\/strong>.<\/li>\n<li>Press <strong>Binding<\/strong>.<\/li>\n<li>Select the binding position and return to the main screen.<\/li>\n<\/ol>\n<p>This administrative setting applies to WSD scanning. It does not replace the selection of long-edge or short-edge binding for a normal scan job to email, a folder, or USB memory.<\/p>\n<h2>Step 4. Configure duplex copying on OKI MB472<\/h2>\n<p><strong>Where the actions are performed:<\/strong> on the MFP button-based control panel. Windows and the printer driver are not involved.<\/p>\n<ol>\n<li>Place the original in the ADF. If the source document is two-sided, using the ADF is required.<\/li>\n<li>Press <strong>COPY<\/strong>.<\/li>\n<li>Use the arrow buttons to open the <strong>Change Settings<\/strong> menu.<\/li>\n<li>Select <strong>Duplex Copy<\/strong> and press <strong>OK<\/strong>.<\/li>\n<li>Select the required combination of source document and finished copy.<\/li>\n<li>Press <strong>OK<\/strong>.<\/li>\n<li>Specify the number of copies.<\/li>\n<li>Press <strong>START<\/strong>.<\/li>\n<\/ol>\n<table style=\"border-collapse: collapse; width: 100%; margin: 18px 0;\">\n<thead>\n<tr>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">Item on the MB472 screen<\/th>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">Result<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Simplex \u2192 Duplex Long Edge<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Single-sided originals are printed on both sides with long-edge binding<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Simplex \u2192 Duplex Short Edge<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Single-sided originals are printed on both sides with short-edge binding<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Duplex \u2192 Duplex<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Both sides of the original are copied onto both sides of the paper<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Duplex Long Edge \u2192 Simplex<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Both sides of a long-edge-bound original are output on separate single-sided sheets<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Duplex Short Edge \u2192 Simplex<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Both sides of a short-edge-bound original are output on separate single-sided sheets<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>If you select <strong>OFF (Simplex)<\/strong>, the MFP will scan and output only a single-sided document.<\/p>\n<h2>Step 5. Configure duplex copying on OKI MB492 and MB562<\/h2>\n<p><strong>Where the actions are performed:<\/strong> on the MFP touch panel.<\/p>\n<ol>\n<li>Place the two-sided original in the ADF face up.<\/li>\n<li>Press <strong>Copy<\/strong> or the physical <strong>COPY<\/strong> button.<\/li>\n<li>On the <strong>Copy<\/strong> or <strong>Basic<\/strong> tab, press <strong>Duplex Copy<\/strong>.<\/li>\n<li>Select <strong>1 \u2192 2<\/strong>, <strong>2 \u2192 1<\/strong>, or <strong>2 \u2192 2<\/strong> mode.<\/li>\n<li>Select long-edge or short-edge binding.<\/li>\n<li>If the orientation of the original is detected incorrectly, press <strong>Change<\/strong> and correct the <strong>Direction<\/strong> setting.<\/li>\n<li>Press <strong>OK<\/strong>.<\/li>\n<li>Specify the number of copies and press <strong>START<\/strong>.<\/li>\n<\/ol>\n<ul>\n<li><strong>1 \u2192 2<\/strong> \u2014 single-sided originals are output on both sides of the paper;<\/li>\n<li><strong>2 \u2192 1<\/strong> \u2014 both sides of the original are output on separate single-sided pages;<\/li>\n<li><strong>2 \u2192 2<\/strong> \u2014 both sides of the original are scanned and printed on both sides.<\/li>\n<\/ul>\n<p>For the first test, use plain A4 paper. If duplex printing of the copy is unavailable, check the paper size, type, and weight in the selected tray. Some small sizes and special media are not suitable for automatic duplex printing.<\/p>\n<h2>Why the platen glass does not scan both sides automatically<\/h2>\n<p><strong>Where the actions are performed:<\/strong> on the platen glass and the MFP control panel.<\/p>\n<p>The platen glass can see only the side facing down. Enabling <strong>Duplex Scan<\/strong> does not allow the machine to turn over an original placed on the glass by itself.<\/p>\n<p>If you need to combine several single-sided pages from the platen glass, use <strong>Continuous Scan<\/strong>: after the first page, the MFP will prompt you to place the next document. Place the next page, select <strong>Start Scan<\/strong>, and after the last page select <strong>Scan Complete<\/strong>.<\/p>\n<p>When copying single-sided pages from the platen glass onto both sides of the paper, continuous scanning may be enabled automatically. However, the ADF is still required to read both sides of one physical sheet automatically.<\/p>\n<h2>Determine the cause from the test result<\/h2>\n<table style=\"border-collapse: collapse; width: 100%; margin: 18px 0;\">\n<thead>\n<tr>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">What happens<\/th>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">Cause<\/th>\n<th style=\"border: 1px solid #c9c9c9; padding: 9px; text-align: left;\">What to do<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Only the front sides are saved when scanning from the control panel<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>OFF<\/strong> is selected for the job<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Enable <strong>Duplex Scan<\/strong> before starting<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Both sides are scanned from the control panel, but only one side from Windows<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">The program, WSD profile, or driver does not pass the duplex setting<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Select the duplex ADF in the program or start scanning from the control panel<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Reverse-side pages are upside down<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">The wrong binding edge is selected<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Change long-edge binding to short-edge binding or vice versa<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Both sides are not scanned from the platen glass<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">The platen glass cannot turn over the original<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Use the ADF or manually turn over the sheet in continuous scanning mode<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>Duplex mode is unavailable for A6<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Device limitation<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Scan the sides separately<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>2 \u2192 2 mode does not print the finished copy<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">The paper size or type in the tray is unsuitable<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Test the job with plain A4 paper<\/td>\n<\/tr>\n<tr>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\"><strong>The sheet jams only when the reverse side is being scanned<\/strong><\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Unsuitable original, dirty rollers, or an ADF reversing mechanism fault<\/td>\n<td style=\"border: 1px solid #c9c9c9; padding: 9px;\">Test with one new, flat A4 sheet; if the jam occurs again, service the ADF<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>When the problem is related to the ADF mechanism<\/h2>\n<p>A mechanical fault should be suspected only after a direct test from the control panel. Enable <strong>Duplex Scan<\/strong>, use one new, flat A4 sheet, and save the file to USB memory, a shared folder, or email.<\/p>\n<p>Contact a service center if one of the following symptoms occurs during this test:<\/p>\n<ul>\n<li>the MFP scans the front side but does not attempt to reverse the sheet to scan the back side;<\/li>\n<li>the sheet stops or jams every time during reversal;<\/li>\n<li>cracking, grinding, or another unusual sound comes from the ADF;<\/li>\n<li>a document feed error appears on the control panel;<\/li>\n<li>the reverse side is missing both when scanning from the control panel and when copying in <strong>2 \u2192 1<\/strong> or <strong>2 \u2192 2<\/strong> mode;<\/li>\n<li>the same problem occurs with several new sheets of plain A4 paper.<\/li>\n<\/ul>\n<p>Do not disassemble the reversing mechanism or pull out a jammed sheet with force. Open only the user-accessible ADF covers and remove the document in the direction shown on the control panel or in the diagram under the cover.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>If a two-sided document passes through the ADF but only the front sides are saved in the file, this usually does not indicate a scanner malfunction. The OKI MB472, MB492 and MB562 support duplex scanning, but it may be disabled&hellip;<\/p>\n<p class=\"more-link-p\"><a class=\"more-link\" href=\"https:\/\/drivernew.com\/?p=78729\">Read more &rarr;<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_lmt_disableupdate":"","_lmt_disable":"","footnotes":""},"categories":[36],"tags":[],"class_list":["post-78729","post","type-post","status-publish","format-standard","hentry","category-oki-printer"],"modified_by":"DriverNew","_links":{"self":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts\/78729","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=78729"}],"version-history":[{"count":1,"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts\/78729\/revisions"}],"predecessor-version":[{"id":78730,"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts\/78729\/revisions\/78730"}],"wp:attachment":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=78729"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=78729"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=78729"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}