\n
Connect the USB cable only when prompted<\/strong><\/p>\nIf you connect the multifunction printer earlier, Windows may create a separate USB device entry, and the installer may not proceed to the correct wireless network setup.<\/p>\n<\/div>\n
Step 3. Run the installer<\/h3>\n\n- Press Windows + E<\/strong>.<\/li>\n
- Open the Downloads<\/strong> folder.<\/li>\n
- Find the file whose name begins with
m68n-win-mg3600-<\/code>.<\/li>\n- Right-click the file.<\/li>\n
- Select Run as administrator<\/strong>.<\/li>\n
- Confirm that you want to run the program.<\/li>\n
- Wait while the files are extracted.<\/li>\n<\/ol>\n
Step 4. Select the wireless connection<\/h3>\n\n- In the \u201cWelcome\u201d<\/strong> window, make sure that the USB cable is disconnected.<\/li>\n
- Change the program language if necessary.<\/li>\n
- Click Next ><\/strong>.<\/li>\n
- In the \u201cLicense Agreement\u201d<\/strong> window, click Yes<\/strong>.<\/li>\n
- In the \u201cConnection Method\u201d<\/strong> window, select Connect the printer to the wireless LAN<\/strong>.<\/li>\n
- Click Next ><\/strong>.<\/li>\n<\/ol>\n
Step 5. Wait for the multifunction printer search<\/h3>\n
The installer will open the \u201cPrinter Detection\u201d<\/strong> window and begin searching for devices on the local network.<\/p>\n\n- Turn on the multifunction printer.<\/li>\n
- Wait until the power lamp stops flashing.<\/li>\n
- Allow the Canon program to access the private network if a firewall prompt appears.<\/li>\n
- Wait until the search is complete.<\/li>\n<\/ol>\n
After the router has been replaced, the multifunction printer is usually not found because it stores the settings of the old network. In this case, the \u201cCheck Printer Settings\u201d<\/strong> window will appear.<\/p>\nStep 6. Select network setup via USB<\/h3>\n\n- In the \u201cCheck Printer Settings\u201d<\/strong> window, select the Set up the network connection via USB<\/strong> checkbox.<\/li>\n
- Click Next ><\/strong>.<\/li>\n
- Wait for the \u201cConnect Cable\u201d<\/strong> window to appear.<\/li>\n<\/ol>\n
The temporary connection allows the installer to communicate directly with the multifunction printer and replace the old network settings with the new ones.<\/p>\n
Step 7. Connect the USB cable<\/h3>\n\n- Connect the almost square USB-B connector to the port on the back of the multifunction printer.<\/li>\n
- Connect the flat USB-A connector directly to the computer.<\/li>\n
- Do not use a USB hub or extension cable.<\/li>\n
- Turn on the multifunction printer if it is turned off.<\/li>\n
- Wait for it to be detected automatically.<\/li>\n<\/ol>\n
After detecting the device, the program will proceed to wireless network selection.<\/p>\n
Step 8. Select the new network<\/h3>\n\n- Wait for the list of available networks to appear.<\/li>\n
- Find the name of the new 2.4 GHz network.<\/li>\n
- Select this network.<\/li>\n
- Click the button to continue.<\/li>\n<\/ol>\n
If the required network is not displayed:<\/p>\n
\n- check whether the 2.4 GHz band is enabled;<\/li>\n
- place the multifunction printer closer to the router;<\/li>\n
- refresh the list of networks;<\/li>\n
- temporarily enable broadcasting of the network name if the SSID is hidden;<\/li>\n
- restart the router.<\/li>\n<\/ul>\n
Step 9. Enter the new password<\/h3>\n\n- Enter the password for the selected network.<\/li>\n
- Pay attention to uppercase and lowercase letters.<\/li>\n
- Do not add spaces at the beginning or end.<\/li>\n
- Check the entered characters.<\/li>\n
- Confirm the settings.<\/li>\n<\/ol>\n
\n
Use the password for the new router<\/strong><\/p>\nDo not enter the Windows account password, the multifunction printer\u2019s administrator password, or the device serial number. To connect through the router, you need the password for the selected Wi-Fi network.<\/p>\n<\/div>\n
Step 10. Complete the transfer of the settings<\/h3>\n\n- Check the name of the selected network.<\/li>\n
- Leave automatic IP address acquisition enabled unless the network requires manual configuration.<\/li>\n
- Confirm the transfer of the settings.<\/li>\n
- Do not turn off the multifunction printer, computer, or router.<\/li>\n
- Wait for the successful connection message.<\/li>\n
- Disconnect the USB cable only after the installer displays the appropriate instruction.<\/li>\n
- Complete the driver installation.<\/li>\n<\/ol>\n
Method 2. Check whether the multifunction printer connected to the new network<\/h2>\n
Canon MG3600 series can print the current network settings.<\/p>\n
\n- Turn on the multifunction printer.<\/li>\n
- Load two sheets of A4 or Letter plain paper.<\/li>\n
- Press and hold the Wi-Fi<\/strong> button.<\/li>\n
- Release the button when the power lamp begins to flash.<\/li>\n
- Press the Wi-Fi<\/strong> button again.<\/li>\n
- Wait for the network information to print.<\/li>\n<\/ol>\n
Check the following lines:<\/p>\n
\n\n\nLine<\/strong><\/td>\nWhat to check<\/strong><\/td>\n<\/tr>\n\n| Wireless LAN<\/td>\n | The wireless function must be enabled.<\/td>\n<\/tr>\n | \n| Connection<\/td>\n | The value Active means that the connection has been established.<\/td>\n<\/tr>\n | \n| SSID<\/td>\n | The name of the new router should be shown.<\/td>\n<\/tr>\n | \n| Signal Strength<\/td>\n | Shows the signal strength.<\/td>\n<\/tr>\n | \n| IP Address<\/td>\n | An address received from the new router should be shown.<\/td>\n<\/tr>\n | \n| Encryption<\/td>\n | Shows the security method being used.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\nIf the printout shows the old network name<\/h3>\nThe new settings were not saved. Repeat the setup using the installer and a temporary USB connection.<\/p>\n If Connection: Inactive is shown<\/h3>\nThe multifunction printer is not connected to the router. Check the password, the 2.4 GHz band, and the network security method.<\/p>\n If Connection: Active is shown<\/h3>\nThe network connection is working. If Windows continues to show the old queue as unavailable, remove the old entry and add the multifunction printer again.<\/p>\n Method 3. Remove the old printer entry from Windows<\/h2>\nAfter the router is replaced, the multifunction printer usually receives a new IP address. The old Windows entry may continue trying to use the previous address.<\/p>\n Windows 11<\/h3>\n\n- Open Start<\/strong> \u2192 Settings<\/strong>.<\/li>\n
- Go to Bluetooth & devices<\/strong>.<\/li>\n
- Open Printers & scanners<\/strong>.<\/li>\n
- Select the non-working Canon MG3600 series entry.<\/li>\n
- Click Remove<\/strong>.<\/li>\n
- Confirm the action.<\/li>\n<\/ol>\n
Windows 10<\/h3>\n\n- Open Start<\/strong> \u2192 Settings<\/strong>.<\/li>\n
- Go to Devices<\/strong>.<\/li>\n
- Open Printers & scanners<\/strong>.<\/li>\n
- Select the non-working Canon MG3600 series entry.<\/li>\n
- Click Remove device<\/strong>.<\/li>\n
- Confirm the action.<\/li>\n<\/ol>\n
After removing it, run the MP Drivers package again and perform the wireless installation.<\/p>\n \n Do not remove a working USB entry unless necessary<\/strong><\/p>\nIf the multifunction printer is also used via USB, Windows may contain two separate entries. Remove only the old or non-working network entry.<\/p>\n<\/div>\n Method 4. Select the network scanner again<\/h2>\nAfter replacing the router, printing may be restored while IJ Scan Utility continues searching for the scanner at the previous network address.<\/p>\n \n- Open the Start<\/strong> menu.<\/li>\n
- Find the Canon Utilities<\/strong> folder.<\/li>\n
- Start IJ Network Scanner Selector EX<\/strong>.<\/li>\n
- Open its settings using the icon in the notification area.<\/li>\n
- Wait for the network device search.<\/li>\n
- Select Canon MG3600 series connected to the new network.<\/li>\n
- Confirm the selection.<\/li>\n
- Close the settings window.<\/li>\n
- Start IJ Scan Utility.<\/li>\n
- Perform a test scan.<\/li>\n<\/ol>\n
If the multifunction printer is not displayed in IJ Network Scanner Selector EX, make sure that the network settings printout shows the new network name and an Active status.<\/p>\n Method 5. Check the new router\u2019s security settings<\/h2>\nAn older multifunction printer may not support some modern router settings.<\/p>\n Wi-Fi band<\/h3>\nEnable the 2.4 GHz band. A network operating only at 5 GHz is not suitable.<\/p>\n WPA3 security<\/h3>\nIf the router is configured for WPA3 only, temporarily change the mode to WPA2-PSK or a compatible mixed mode that allows WPA2 devices to connect.<\/p>\n Guest network<\/h3>\nDo not connect the multifunction printer to a guest network if device isolation is enabled. On such a network, the computer may have internet access but may be unable to detect the printer.<\/p>\n MAC address filtering<\/h3>\nIf the router allows connections only from registered devices, add the multifunction printer\u2019s MAC address. It is shown on the network settings printout.<\/p>\n DHCP<\/h3>\nMake sure that the DHCP server is enabled. It assigns a new IP address to the multifunction printer.<\/p>\n Client isolation<\/h3>\nCheck for settings with the following or similar names:<\/p>\n \n- AP Isolation;<\/li>\n
- Client Isolation;<\/li>\n
- Wireless Isolation;<\/li>\n
- wireless device isolation;<\/li>\n
- block access to the local network.<\/li>\n<\/ul>\n
For standard printing and scanning between the computer and multifunction printer, this isolation must be disabled.<\/p>\n Method 6. Enable the wireless function on the multifunction printer<\/h2>\nIf the Wi-Fi lamp is not lit, the wireless function may be disabled.<\/p>\n \n- Make sure that the multifunction printer is turned on.<\/li>\n
- Press and hold the Wi-Fi<\/strong> button.<\/li>\n
- Release it when the power lamp begins to flash.<\/li>\n
- Press the Color<\/strong>, Black<\/strong>, and Wi-Fi<\/strong> buttons in sequence.<\/li>\n
- Wait until the power lamp stops flashing.<\/li>\n
- Make sure that the Wi-Fi lamp lights up.<\/li>\n<\/ol>\n
After this, repeat the installation and transfer the new network settings.<\/p>\n Method 7. Perform a full reset of the multifunction printer settings<\/h2>\nUse this method only if the multifunction printer continues to store incorrect network settings and standard repeated setup does not help.<\/p>\n \n A full reset removes more than just the Wi-Fi settings<\/strong><\/p>\nAfter this procedure, the device settings return to their original values. Use it only after trying the simpler methods.<\/p>\n<\/div>\n How to perform the reset<\/h3>\n\n- Make sure that the multifunction printer is turned on.<\/li>\n
- Press and hold the Stop<\/strong> button.<\/li>\n
- Watch the Alarm lamp.<\/li>\n
- Release the Stop<\/strong> button when the Alarm lamp flashes 21 times.<\/li>\n
- Wait for the reset to finish.<\/li>\n
- Turn off the multifunction printer.<\/li>\n
- Wait approximately 10 seconds.<\/li>\n
- Turn on the multifunction printer again.<\/li>\n<\/ol>\n
After the reset, run the MP Drivers package and perform the wireless setup again.<\/p>\n If the installer does not detect the multifunction printer via USB<\/h2>\nDuring temporary network setup, the installer must detect the multifunction printer through the cable.<\/p>\n If the \u201cConnect Cable\u201d<\/strong> window does not close automatically:<\/p>\n\n- Make sure that the multifunction printer is turned on.<\/li>\n
- Check whether the error lamp is lit.<\/li>\n
- Insert the cable firmly into the port on the back of the multifunction printer.<\/li>\n
- Connect the cable directly to the computer.<\/li>\n
- Do not use a USB hub or extension cable.<\/li>\n
- Try another USB port.<\/li>\n
- If another working cable is available, test it.<\/li>\n
- Turn off the multifunction printer.<\/li>\n
- Disconnect and reconnect the USB cable.<\/li>\n
- Turn on the multifunction printer.<\/li>\n<\/ol>\n
If the device is not detected, cancel the installation, restart the computer, and begin the procedure again.<\/p>\n How to check the result<\/h2>\nAfter setup, disconnect the temporary USB cable and check wireless printing.<\/p>\n Check printing<\/h3>\n\n- Make sure that the multifunction printer and new router are turned on.<\/li>\n
- Disconnect the USB cable.<\/li>\n
- Load several sheets of paper.<\/li>\n
- Press Windows + R<\/strong>.<\/li>\n
- Enter the following command:<\/li>\n<\/ol>\n
control printers<\/pre>\n\n- Click OK<\/strong>.<\/li>\n
- Find Canon MG3600 series.<\/li>\n
- Right-click the device.<\/li>\n
- Select Printer properties<\/strong>.<\/li>\n
- Click Print Test Page<\/strong>.<\/li>\n<\/ol>\n
Check scanning<\/h3>\n\n- Open IJ Network Scanner Selector EX.<\/li>\n
- Select the network version of MG3600 series.<\/li>\n
- Start IJ Scan Utility.<\/li>\n
- Place a document on the platen glass.<\/li>\n
- Select the appropriate scanning mode.<\/li>\n
- Wait for the file to be saved.<\/li>\n<\/ol>\n
If Windows shows \u201cOffline\u201d after setup<\/h2>\nFirst, complete the following steps:<\/p>\n \n- Make sure that the USB cable is disconnected.<\/li>\n
- Check whether the Wi-Fi lamp is lit.<\/li>\n
- Print the network settings.<\/li>\n
- Check the new network name and Active status.<\/li>\n
- Restart the multifunction printer.<\/li>\n
- Restart the computer.<\/li>\n
- Remove the old MG3600 series network entry.<\/li>\n
- Reinstall MP Drivers.<\/li>\n<\/ol>\n
If the problem occurs again after every router restart, it may be related to a changing IP address or an incorrect Windows network port. This situation requires a separate check of the port settings.<\/p>\n Important information for Windows 11 ARM<\/h2>\n\n The official installer may not work completely on an ARM computer<\/strong><\/p>\nOn laptops with Qualcomm Snapdragon X Elite, Snapdragon X Plus, or Microsoft SQ processors, the network printer may be added using Windows features, but the Canon programs and scanner driver may not be installed.<\/p>\n If the MP Drivers package does not run, first connect the multifunction printer to the new router using a compatible computer or mobile device, and then try adding it under Printers & scanners.<\/p>\n<\/div>\n Frequently asked questions<\/h2>\nWhy did the multifunction printer not connect to the new router automatically?<\/h3>\nThe device stores the name, password, and security settings of the previous network. If at least one setting has changed, the connection must be configured again.<\/p>\n Can I assign the old name and password to the new router?<\/h3>\nYes. If you use the previous network name, password, and a compatible security method, the multifunction printer may connect automatically.<\/p>\n Why did using the same name and password not help?<\/h3>\nThe cause may be a disabled 2.4 GHz band, WPA3-only security, a guest network, MAC address filtering, or device isolation.<\/p>\n Do I need to remove the driver after replacing the router?<\/h3>\nNot always. First, transfer the new network settings to the multifunction printer. If Windows continues using the old unavailable entry, remove it and reinstall MP Drivers.<\/p>\n Can I change only the Wi-Fi password without reinstalling?<\/h3>\nThe new password must be transferred to the multifunction printer. A convenient way to do this is to run the installer again and select network connection setup via USB.<\/p>\n Will the USB cable be required permanently?<\/h3>\nNo. During wireless network setup, the cable is used temporarily. It should be disconnected after the connection to the router has been established successfully.<\/p>\n Why was printing restored but scanning was not?<\/h3>\nIJ Network Scanner Selector EX may continue using the previous network entry. Select MG3600 series again after connecting it to the new router.<\/p>\n Can the multifunction printer connect to a 5 GHz network?<\/h3>\nNo. Canon MG3600 series uses a 2.4 GHz wireless network.<\/p>\n When is a full reset required?<\/h3>\nA full reset should be used if the multifunction printer continues to store incorrect settings, remains in an unsuitable mode, or does not accept the new settings using the standard method.<\/p>\n Why does the printout show the new SSID, but Windows does not print?<\/h3>\nThe multifunction printer is connected to the new router, but Windows may be using the old IP address or old print queue. Remove the non-working entry and add the device again.<\/p>\n Conclusion<\/h2>\nAfter replacing the router or changing the password, the new wireless network settings must be transferred to Canon PIXMA MG3600 series. The most reliable method is to run the MP Drivers package again, select the wireless LAN connection, and use a temporary USB connection.<\/p>\n In the \u201cCheck Printer Settings\u201d<\/strong> window, select the \u201cSet up the network connection via USB\u201d<\/strong> checkbox. Connect the cable only after the prompt appears, select the new 2.4 GHz network, and enter its password.<\/p>\nWhen the setup is complete, disconnect the USB cable, print the network settings, and make sure that the new network name and Active status are shown. If Windows continues to show the old entry as unavailable, remove it and reinstall the network printer.<\/p>\n","protected":false},"excerpt":{"rendered":" After replacing the router or changing the wireless network name or password, Canon PIXMA MG3600 series may stop printing and scanning over Wi-Fi. In Windows, the device often remains in the list but is shown as unavailable or has an…<\/p>\n Read more →<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_lmt_disableupdate":"","_lmt_disable":"","footnotes":""},"categories":[27],"tags":[],"class_list":["post-78622","post","type-post","status-publish","format-standard","hentry","category-canon"],"modified_by":"DriverNew","_links":{"self":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts\/78622","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=78622"}],"version-history":[{"count":1,"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts\/78622\/revisions"}],"predecessor-version":[{"id":78623,"href":"https:\/\/drivernew.com\/index.php?rest_route=\/wp\/v2\/posts\/78622\/revisions\/78623"}],"wp:attachment":[{"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=78622"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=78622"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/drivernew.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=78622"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}} | | |